How to Replace LEAPMOTOR B10 & C10 TPU Steering Wheel Protective Film
The factory leather steering wheel on LEAPMOTOR B10 and C10 will gradually wear, turn yellow and accumulate sweat stains after long daily driving. Finger nails, jewelry and palm oil cause irreversible scratches, which degrade the interior texture and reduce vehicle resale value. Many LEAPMOTOR owners choose our model-specific clear TPU steering wheel film for invisible protection, yet most beginners struggle with uneven sticking, trapped air bubbles and messy glue residue during replacement.
This detailed DIY guide walks you through removing old film and installing new TPU wheel film step by step, designed exclusively for LEAPMOTOR B10 and C10. Each film is cut via 1:1 original car 3D scanning, matching all button gaps, sensor areas and wheel radian perfectly. The installation process requires only simple household supplies, no professional tools or car shop fees, and works for all 2023-2026 LHD and RHD LEAPMOTOR B10 & C10 variants.
Pre-Install Preparation & Package Check
Before you start replacing the wheel film, prepare all included accessories and auxiliary tools:
1. Custom pre-cut TPU steering wheel film for LEAPMOTOR B10/C10
2. Alcohol cleaning wipes, microfiber soft cloth, plastic squeegee scraper
3. Small spray bottle filled with pure water (mixed with tiny drop of neutral soap)
Pre-install tips:
- Park your LEAPMOTOR in a cool, shaded room; avoid installation under high-temperature direct sunlight, which makes TPU film sticky instantly and hard to adjust.
- Turn the steering wheel to horizontal position for full access to the entire wheel surface.
- If you are replacing old worn film, tear the existing TPU film slowly at a 45-degree angle to avoid leaving adhesive residue on leather.
Step-by-Step Replacement & Installation Process
Step 1: Deep clean the whole steering wheel surface
Wipe the leather wheel thoroughly with alcohol wipes to erase sweat, oil, dust and wax buildup. Wait 3 minutes until the wheel is completely dry; any grease will cause the new film to peel off quickly.
Step 2: Spray tiny amount of soapy water on the adhesive side of TPU film
Light misting lets you reposition the film freely without instant sticking, which eliminates misalignment and bubble risks completely. Do not spray excessive liquid to avoid soaking wheel buttons.
Step 3: Dry fit and align the film on steering wheel
Place the pre-cut TPU film onto the wheel, match the reserved cutouts with multi-function control buttons, confirm the top, bottom and side radian align perfectly with original wheel shape. Adjust position until no offset exists.
Step 4: Squeeze out water and air bubbles from center to edges
Use the soft plastic squeegee to press firmly from the middle of film outwards, pushing all water and trapped air to the film edges. Focus on curved grip areas and button cutouts to flatten every wrinkle.
Step 5: Peel off transparent surface protective layer
After all bubbles are removed, gently tear away the top clear PET protective film from the TPU layer, wipe excess water with microfiber cloth, then leave the wheel to air dry for 1 hour.
Step 6: Final inspection
Check all button gaps, wheel grip edges and sensor positions to ensure no film overlaps functional areas. Test steering wheel heating and multi-function buttons to confirm zero interference with original car functions.
Common Mistakes To Avoid During Replacement
1. Install under hot sun: High temperature makes TPU adhesive stick instantly, unable to reposition and creates permanent bubbles.
2. Skip alcohol cleaning: Oil residue under film leads to peeling within weeks of driving.
3. Tear film violently when removing old protector: Causes sticky glue leftover on leather wheel, hard to clear.
4. Use universal uncut wheel film: Generic wraps block control buttons and sensors, leaving uneven gaps.
5. Over-spray liquid on film: Extra water seeps into button gaps and damages internal electronic components.
Long-Term Benefits After Correct Installation
The ultra-thin automotive-grade TPU film restores the original soft touch of your LEAPMOTOR steering wheel without bulky feeling. It features self-healing performance for tiny scratch marks, isolates sweat and oil corrosion to prevent leather yellowing and cracking. The invisible transparent design retains the factory minimalist interior style, while extending the service life of your original steering wheel for multiple years. When you need to replace the film later, it peels off cleanly with zero residual glue on leather.
Final Tips
To organize your LEAPMOTOR interior space better, check our previous installation guide: How to Install LEAPMOTOR B10 & C10 Center Console Organizer Tray. Shop tailor-made LEAPMOTOR B10 & C10 TPU Steering Wheel Protective Film from NiceEVS and protect your original steering wheel easily with DIY replacement!