How to Install XPENG Full Range Door Anti-Kick Mats (No Residual Glue)
Custom OEM door anti-kick mats are essential interior protective accessories for all XPENG electric vehicles, blocking heel scratches, shoe stains, kid footprints and mud marks to keep the original door panel intact and maintain the car’s resale value. Most XPENG owners worry about leftover adhesive residue, misaligned fitting and bubbling after installation, which ruins the original interior texture. This official NiceEVS tutorial shares a professional damage-free installation method with zero glue residue, suitable for XPENG G6, G9, P5, P7 and all mainstream models, compatible with both LHD European versions and RHD Southeast Asian overseas variants from 2023 to 2026.
Our XPENG dedicated anti-kick mats adopt 1:1 3D scanning molding to match each model’s door radian, pre-attached with high-viscosity automotive 3M adhesive tape. The adhesive is specially processed to avoid permanent residue on plastic and leather door panels after removal. The whole installation only takes 10 minutes per four-door set, no professional tools or modification experience required for novice EV owners.
Pre-Install Preparation & Package Inspection
Before installation, check the complete accessory package: 4pcs model-specific XPENG door anti-kick mats, alcohol cleaning wipes, auxiliary pressing scraper and installation instruction card. No extra cutting tools or drilling equipment are needed.
Key pre-install tips:
1. Park your XPENG car in a dry, room-temperature environment (avoid installing under direct high-temperature sunlight or cold rainy days).
2. Open all four car doors fully for convenient operation, roll down windows to prevent accidental scratches.
3. Thoroughly wipe the lower door panel area with the supplied alcohol wipe to remove dust, oil, shoe polish and wax, then wait 2 minutes for the surface to fully dry. Dust and grease will cause poor adhesion and easy falling off.
Step-by-Step No-Residue Installation Process
Step 1: Dry-fit the anti-kick mat on the corresponding door panel without peeling off the backing film. Align the mat’s edge with the door storage slot and speaker cutout to confirm the perfect position, mark the alignment line lightly with your finger.
Step 2: Tear off only 1/3 of the adhesive backing paper from the top edge of the mat first, do not remove the whole film at once to avoid misalignment caused by sudden sticking.
Step 3: Attach the aligned top part to the door panel, press firmly with the auxiliary scraper from the center to both sides to squeeze out air bubbles completely.
Step 4: Gradually tear off the remaining backing paper section by section, keep scraping and pressing the mat surface to eliminate hidden bubbles and wrinkles along the door radian.
Step 5: Focus on the curved edge and speaker hole position, repeatedly press for 30 seconds to strengthen adhesion. Repeat the same operation for the front passenger door, rear left and rear right doors.
Step 6: After finishing all four doors, close the doors and let the adhesive set for 2 hours before carrying passengers to prevent shifting from heel impact.
Common Installation Mistakes to Avoid
1. Install on dirty or wet door panels: Grease and moisture will weaken adhesive viscosity, leading to mat peeling after weeks of use.
2. Peel off the entire backing film at once: Hard to reposition once it sticks, creating uneven gaps and ugly bubbles.
3. Skip post-install pressing: Air bubbles trapped under the mat will expand under high temperature, causing warping edges.
4. Use universal anti-kick pads: Only model-exclusive XPENG mats reserve speaker and storage slot cutouts; generic pads will block door functions and leave obvious gaps.
5. Pull off the mat violently when removing: Tear slowly at a 45° angle to ensure zero residual glue on the original door panel.
Post-Install Benefits
After standard installation, the XPENG door anti-kick mats fit seamlessly with the factory door panel without bulges or mismatched edges. The matte TPE surface resists daily heel friction and liquid stains, and can be wiped clean with a damp tissue in seconds. The invisible protective design retains XPENG’s minimalist interior style while extending the service life of original door trim, effectively reducing interior maintenance costs for long-term driving.
Final Shopping & Installation Tips
We only supply model-dedicated EV interior accessories without ill-fitting universal parts. You can check our previous article about <a href="https://niceevs.com/blog/zeekr-7x-mud-flaps-install">How to Install Mud Flaps on ZEEKR 7X (No Drilling)</a> for more exterior accessory DIY guides. Purchase tailor-made XPENG Full Range Door Anti-Kick Mats from NiceEVS, follow this tutorial to finish damage-free installation at home, and fully protect your XPENG’s original interior!